aluminum wall panels Wall Construction Simplified

by:Carlos     2019-04-04
The wall was built as two main components,They are structures,And complete the material.This structure is used to provide service utilities,Support the upper part of the building,As an attachment to the finished material or insulation.They were built in two major departments.Interior walls,And exterior walls.The interior wall structure is divided into two categories,load bearing,and non-load bearing.Although not common,Many homeowners choose to isolate the wall system to reduce sound transmission and heat loss in unused rooms.Interior load-The load-bearing wall is mainly composed of 2 "x 4", or 2 "x 6", Wood of sizeWith two roof plates,And a bottom plate,The nail-to-vertical member is called a "stud" with an interval of 16 ".They are above the bearing beam,Columns or footprints,Ability to support the load that will be placed on them.Most often,load-Vertical Installation of bearing walls,As the support of the upper support beam,Ceiling beams or frame roof assemblies.Installation and head in the opening of the load-bearing wall,Or small beams,Support short studs,The height and width required to cross the opening in the wall.Cross support is usually required to prevent parallel deformation of external forces,And hold the building square.Interior non-The load-bearing wall is installed in a position where the superstructure members do not rest or do not require support.They are usually made of single top and bottom plates,with studwork,Usually in 24 centers.Nailed them.The position of using this type of wall includes a wall parallel to the beam,Work in a building with a definite span truss or a manufacturing/frame support beam.The openings of these walls generally do not require the use of structural heads or supports,But diagonal supports are often needed to prevent lateral movement.The exterior walls always provide support for the superstructure,Floor and roof components are included.They always load-bearing,Diagonal support or shear plate is required,And enough insulation space.In Northern OntarioThese walls are generally constructed from 2 "x 6" materials,But the insulation structure is usually added to the two-wall system.In the Wall component,Windows and doors are installed to provide access to the building,And an indoor environment that allows natural light or ventilation.They are constructed from the frame of the stud,Usually 16 "apart,Nailed to a double roof,And single bottom plate.In the cavity,Practical wiring and insulation placement.The internal surface is treated with a vapor barrier,and finish,There is an air barrier with an external surface and an external finish or "siding" for installation.The opening is framed by a beam or line frame,Support short studs,Called "Jack"And nailed to the top and bottom plates.Although there are many configurations,Builders use,Diagonal support,It is most often installed as a clipboard,Sheets of plywood or poplarNailed to the outside of the wall frame.Other methods of diagonal support include wood or metal wind support, which is a component placed diagonally from the bottom plate,Through studs,To the top plate.There are two main areas on the wall, in which the application will be completed,They include internal exposed surfaces and external exposed surfaces.The finished material provides an aesthetic surface,Protect utility lines,And reduce the transmission of sound and heat.The finish applied to the interior wall is a very important consideration for the owner.This is the surface,They will see every day,And must have visual appeal.yet,Durable and requires minimal maintenance.Many completed,We will discuss the panel,gypsum board,Wood with interlocking.Panels are thin wood products,Usually the size of 4' x 8,To complete the texture with various,Color and pattern.It is manufactured for general position,But some types can be installed in wet areas,Like shower and laundry.It's easy to wear,There is no need to finish the work except trim and block,when required.The advantage of this type of completion is that it can be installed quickly without maintenance or maintenance.One drawback is that it is usually only a few years to complete,So the future fixIt is often necessary to completely replace the damaged panel,And all adjacent panels,Make sure to match.Gypsum board (Often referred to by the trade name as "dry wall"May be the most common internal finish for installation.Smooth plasterboard,Flat surface finish,This is durable,Can change its appearance by painting,Easy to fix and requires minimal maintenance.It's a relatively cheap installation,But it's often a bit confusing.This is due to the need for repeated coating of gypsum based compounds,Need to fill in all joints and penetration between individual drawings,This needs to be polished down.It's a good sound and a thermal barrier,Smooth and light in it-Color surfaces can easily reflect sound waves,And radiate heat,Back in the room.Interlocking wood finish,It is a very natural surface treatment.They're just wood,Interlocking design.This type of completion,Can be made from oak,birch,maple,cedar,Or the most common,pine.The installer usually uses small nails to secure individual slats,But they tend to choose the glue part in place.This type of completion requires trimming work to hide any exposed edges.Interlocking wood,More expensive to install,Due to material costs,And higher hours of labor.It needs to be sealed occasionally with a shell,sealers,oils,Or keep stains,And the repair work is quite difficult.The end of this type,Is the most often installed in the need for less noise,like dens,Living room or library.The finish applied to the surface of the exposed wall is an important consideration for the owner.This is the surface,Neighbors and passers-by will seeeach day,And must have visual appeal.yet,Durable and requires minimal maintenance.Many completed,We will discuss the panel,Vinyl or aluminum siding,brick,Wood with interlocking.Panels are thin wood products,Usually the size of 4' x 8,And equipped with a variety of finished textures,Color and pattern.It is manufactured for external positions.It's easy to install,There is no need to finish the work except trim and block.The advantage of this type of completion is that it can be installed quickly and requires very little maintenance or maintenance.One drawback is that it is usually only a few years to complete,Therefore, future maintenance often requires a complete replacement of damaged panels,And all adjacent panels,Make sure to match.Vinyl or aluminum siding is the most popular type of siding at present,Installed in a modern home.It is a product made of extrusion,Or press the polyethylene base through the mold,Or shaped by stamping aluminum plates.It has a variety of colors and textures,And different widths.It is fixed in buildings with small,large-headed nails,This is left loose allowing thermal expansion.This is a lasting,Maintenance Free type finish,A long life span.Because of this,In fact, it's a cheaper side-to-side installation,It is often the choice of builders.The only drawback of this kind of siding is that it is easy to damage,And maintenance is difficult,at best,to make.The most durable and expensive,External completion,It is a popular brick siding.Bricks are made of clay or cement,Small 4 "x 3-forming or extrusion-1/2 "x 8" bricks (typically).They have many colors,And a variety of textures.Other types of brick siding can include rocks or stones,cut to fit.The brick is installed in a mortar bed unit of 1/2,Called Union,And connect to the wall to connect with the brick.The mortar can color the accent or match the brick.Brick siding is a very durable and maintenance-free finish,No maintenance or maintenance required,At the same time give the home a very solid or irritable feeling.It is quite expensive to install but still a popular choice for modern buildings.Interlocking wood finish,It is a very natural surface treatment.They are simple wooden strips,Interlocking design.This type of finish can be made from pine trees,Or more oftencedar.The installer uses small-Galvanized nails to secure individual slats.Interlocking wood needs to be trimmed to hide any exposed edges,And block seal external penetration.This is a moderately expensive complete installation,Due to material costs,And higher hours of labor.It needs to be sealed occasionally with a shell,sealers,oils,Or keep stains,And the repair work is quite difficult.The end of this type,Most often installed in the location of a cottage or rural building because of its natural appearance.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...