aluminum panels for walls Easy Steps to Install Drywall Panels

by:Carlos     2019-04-04
There are 3 types of Gypsum Board (Based on thickness.1.1/2 to 16 inch or less-This type of drywall is suitable for use with walls.But if you are plastering the old wall, the thickness you should use is 3/8 inch.2.5/8 to 24 inch-The ceiling panel should always be thicker than the dry wall thickness used in the wall.3.1/2 waterproof-Wet areas such as bathrooms (The mildew-proof gypsum board is used in the basement).In areas with direct and indirect contact with water,You need to use the waterproof panel.Also remember this area with the presence of the mold;You need to use the mold proof drywall panel.Gypsum board is available in different sizes and sizes.Some are 4x8 or 4x12, if you are closer to the main manufacturer,You can find bigger sheets with ceilings like 14ft-54ft length and 9ft width.The 4x8 panel weighs 55 lbs while the 4x12 panel weighs 82 pounds.1.Ensure proper wood support is available in areas where plasterboard is not supported.Check each corner and ceiling or wall joint.2.Use T-to measure the correct length of the desired panelsquare.From the entire panel,Cut the required length using a utility tool knife and cut the panel on the back.Make sure to cut and smooth edges correctly using the surform tool.The gap between panels should be less than 1/4 inch.Note:The 4x8 panel can cover 32 square meters.The Ft and 4x12 panels can cover 48 square meters.ft.If you can, order enough plasterboard to complete the whole project.If you're a few short panels,It's better to run faster and add more panels than stock extra panels that you will never use.3.Install the drywall panel on the ceiling first, then proceed to the wall.You need an assistant to connect the drywall panel to your wall and ceiling.Install 12 ft or larger panels to your ceiling using an elevator.Keep the right position of the panel and pre-Nail plate.Once the panel is in place,Fix the panel using drywall screws.Perform this process on the entire ceiling.The additional panels are easier on the ceiling because they are a flat surface and they do not cut very porous (Except for a few light bulb patternsDifferent from the wall you need to cut the pattern for the window,doors,Sockets and others.When cutting patterns for bulbs on the ceilingoutlets,doors,Windows and small openings you can cut with a spiral -?out saw.4.Once you finish the ceiling,Start cutting the panels of the walls,The windows and doors are cut using a drywall saw or a small hole saw.Use the T-The square is straight lines and the drywall panel is cut using a utility tool knife.The lock hole saw is also used to cut sockets and other small cutting modes.5.Install gypsum board on your wall,Before fastening the panel, make sure to push the panel tightly to the edge of the ceiling.Avoid breaking joints on the edge of windows and doors as they eventually crack, which can also be a problem when you start recording.6.Fix the panel to the wall using drywall screws.Longer nails and screws are not advisable as they are easier to pop up.Nails are used only for support or auxiliary support,So the screws are the main fasteners.That's why putting the drywall screws in place is the last step you need to do after putting all the drywall panels in their position.7.Use the putty knife on each screw and nail head to check the protruding screws and nails.If you hear a click,Then your nails or screws need to be pushed further-.After a long process of installing drywall panels,What you need to do next is recording.The reason why you need the right nails is that they will show and become a huge distraction when you start recording.For the quick work of recording,Especially in the corner.You will use a drywall putter.It is best to use plasterboard in the corners as they have smooth flat blades evenly distributing mud to the corners.On the other hand, an application,Although they can be used in cornersApplied to evenly spread mud on a flat surface,Edge and curved area.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...